NetApp存储无法开机问题处理-(初始化重装系统)

发布时间:2020-07-08 14:28:13 作者:qingfenghaha
来源:网络 阅读:4587

测试环境:    
原有存储是两个独立控制器+磁盘柜,目前是一个控制器+磁盘柜。开机启动时,先开启扩展柜,一分钟后开启控制器。发现系统起不来,经过多次尝试失败后,决定通过维护模式进入系统进行查看。(类似于Windows7的维护模式一样)

问题处理:    
开机boot启动项,按Ctrl+C命令中断正常启动,进入到boot menu菜单。    
Starting AUTOBOOT press Ctrl-C to abort...    
Loading X86_64/freebsd/p_w_picpath2/kernel:0x200000/10088648 0xb9f0c8/4301024 Entry at 0x80271e20    
Loading X86_64/freebsd/p_w_picpath2/platform.ko:0xfba000/1990365 0x11a0000/296352 0x11e85a0/273360    
Starting program at 0x80271e20    
NetApp Data ONTAP 8.3.1P2    
Copyright (C) 1992-2015 NetApp.    
All rights reserved.    
Checking boot device filesystem    
** /dev/da0s1    
** Phase 1 - Read and Compare FATs    
** Phase 2 - Check Cluster Chains    
** Phase 3 - Checking Directories    
** Phase 4 - Checking for Lost Files    
69 files, 1011584 free (31612 clusters)    
MARK FILE SYSTEM CLEAN? yes    
MARKING FILE SYSTEM CLEAN    
Retry #1 of 5: /sbin/fsck_msdosfs /dev/da0s1    
Retry #2 of 5: /sbin/fsck_msdosfs /dev/da0s1    
Repaired boot device filesystem    
*******************************    
*                             *    
* Press Ctrl-C for Boot Menu. *    
*                             *    
*******************************     
^CBoot Menu will be available.

WARNING:  The battery is unfit to retain data during a power  
          outage.  This is likely because the battery is    
          discharged but could be due to other temporary    
          conditions.    
          When the battery is ready, the boot process will    
          complete and services will be engaged.    
          To override this delay, press 'c' followed by 'Enter'    
c

CAUTION: Using this appliance without NVRAM  
         battery backup coupled with a power    
         failure condition CAN CAUSE DATA LOSS.    
Are you sure you want to continue (y or n)? y    
Proceeding without NVRAM battery backup.

Please choose one of the following:

(1) Normal Boot.        #正常启动    
(2) Boot without /etc/rc.   #启动存储时,不执行/etc/rc设置参数    
(3) Change password.      #如果忘记了超级用户密码,可以在此修改    
(4) Clean configuration and initialize all disks. #清除配置,初始化所有的磁盘    
(5) Maintenance mode boot.  #进入维护模式,当系统进不去的时候可以尝试用维护模式进入    
(6) Update flash from backup config. #从备份配置中升级flash    
(7) Install new software first.    #安装新的软件    
(8) Reboot node.         #重启节点    
Selection (1-8)? 5    
ixgbe: e1a: ** JUMBOMBUF DEBUG ** switching to large buffers(9k -> 3k): (sz = 5120)!    
ixgbe: e1b: ** JUMBOMBUF DEBUG ** switching to large buffers(9k -> 3k): (sz = 5120)!    
ixgbe: e2a: ** JUMBOMBUF DEBUG ** switching to large buffers(9k -> 3k): (sz = 5120)!    
ixgbe: e2b: ** JUMBOMBUF DEBUG ** switching to large buffers(9k -> 3k): (sz = 5120)!    
Ipspace "iwarp-ipspace" created    
WAFL CPLEDGER is enabled. Checklist = 0x7ff841ff    
add host 127.0.10.1: gateway 127.0.20.1    
5    
    You have selected the maintenance boot option:    
    the system has booted in maintenance mode allowing the    
    following operations to be performed:    
    ?                     acorn            
    acpadmin              aggr             
    cna_flash             disk             
    disk_latency          disk_list        
    disk_mung             disk_shelf       
    diskcopy              disktest         
    dumpblock             environment      
    fcadmin               fcstat           
    fctest                fru_led          
    ha-config             halt             
    help                  ifconfig         
    key_manager           led_off          
    led_on                nv8              
    raid_config           sasadmin         
    sasstat               scsi             
    sesdiag               sldiag           
    storage               stsb             
    sysconfig             systemshell      
    ucadmin               version          
    vmservices            vol              
    vol_db                vsa              
    xortest          
    Type "help <command>" for more details.

    In a High Availablity configuration, you MUST ensure that the    
    partner node is (and remains) down, or that takeover is manually    
    disabled on the partner node, because High Availability    
    software is not started or fully enabled in Maintenance mode.

    FAILURE TO DO SO CAN RESULT IN YOUR FILESYSTEMS BEING DESTROYED

    NOTE: It is okay to use 'show/status' sub-commands such as  
    'disk show or aggr status' in Maintenance mode while the partner is up    
Continue with boot? y    
y    
Ipspace "acp-ipspace" created    
original max threads=40, original heap size=41943040    
bip_nitro Virtual Size Limit=79455027 Bytes    
bip_nitro: user memory=724406272, actual max threads=41, actual heap size=43201331    
WARNING: Giving up waiting for mroot    
Tue Feb 14 07:59:49 UTC 2017    
*> ? #可以看到在维护模式下支持的命令参数    
?                   disktest            key_manager         stsb               
acorn               dumpblock           led_off             sysconfig          
acpadmin            environment         led_on              systemshell        
aggr                fcadmin             nv8                 ucadmin            
cna_flash           fcstat              raid_config         version            
disk                fctest              sasadmin            vmservices         
disk_latency        fru_led             sasstat             vol                
disk_list           ha-config           scsi                vol_db             
disk_mung           halt                sesdiag             vsa                
disk_shelf          help                sldiag              xortest            
diskcopy            ifconfig            storage            
*> disk show    
Local System ID: 1575136460

  DISK       OWNER                    POOL   SERIAL NUMBER         HOME                    DR HOME    
------------ -------------            -----  -------------         -------------           -------------           
0a.10.6      sz-3240-02(1575136687)    Pool0  LXW6RH4M              sz-3240-02(1575136687)                        
0b.10.7      sz-3240-02(1575136687)    Pool0  LXW63XYM              sz-3240-02(1575136687)                        
0a.10.2      sz-3240-01(1575136460)    Pool0  LXW72ZGM              sz-3240-01(1575136460)                        
0b.10.5      sz-3240-01(1575136460)    Pool0  LXW1W02M              sz-3240-01(1575136460)                        
0b.10.11     sz-3240-02(1575136687)    Pool0  LXW6364M              sz-3240-02(1575136687)                        
0a.10.8      sz-3240-02(1575136687)    Pool0  LXV3HE7L              sz-3240-02(1575136687)                        
0b.10.9      sz-3240-02(1575136687)    Pool0  LXW5YNSM              sz-3240-02(1575136687)                        
0a.10.4      sz-3240-01(1575136460)    Pool0  LXWT76HL              sz-3240-01(1575136460)                        
0b.10.3      sz-3240-01(1575136460)    Pool0  LXW6ELRM              sz-3240-01(1575136460)                        
0a.10.10     sz-3240-02(1575136687)    Pool0  LXW6DTTM              sz-3240-02(1575136687)                        
0b.10.1      sz-3240-01(1575136460)    Pool0  LXW6R84M              sz-3240-01(1575136460)                        
0a.10.0      sz-3240-01(1575136460)    Pool0  LXV3GV4L              sz-3240-01(1575136460)                        
由上图可以看到,存储12块磁盘被平均分配到了两个控制器上,由于目前只有一个控制器,所以很有可能系统在另外一个控制器上,而另外一个控制器缺少,导致开机无法启动。    
现在手工把所有的磁盘都分配到当前控制器上。      
*> disk reassign -s 1575136687 -d 1575136460 
#把1575136687控制器上的磁盘都重新分配给1575136460控制器    
#reassign {-s <old_sysid>} [-d <new_sysid>] [-p <partner_sysid>]- reassign disks from old filer    
Partner node must not be in Takeover mode during disk reassignment from maintenance mode.    
Serious problems could result!!    
Do not proceed with reassignment if the partner is in takeover mode. Abort reassignment (y/n)? n    
After the node becomes operational, you must perform a takeover and giveback of the HA partner node to ensure disk reassignment is successful.    
Do you want to continue (y/n)? y    
Disk ownership will be updated on all disks previously belonging to Filer with sysid 1575136687.    
Do you want to continue (y/n)? y    
Cannot do remote rescan. Use 'run local disk show' on the console of sz-3240-01 for it to scan the newly assigned disks    
Feb 14 08:04:52 [sz-3240-01:diskown.RescanMessageFailed:warning]: Could not send rescan message to sz-3240-01. Use the "disk show" command in nodeshell of sz-3240-01 for it to scan the newly inserted disks.    
*> disk show                               
Local System ID: 1575136460

  DISK       OWNER                    POOL   SERIAL NUMBER         HOME                    DR HOME    
------------ -------------            -----  -------------         -------------           -------------           
0a.10.6   sz-3240-01(1575136460)    Pool0  LXW6RH4M              sz-3240-01(1575136460)                        
0b.10.7   sz-3240-01(1575136460)    Pool0  LXW63XYM              sz-3240-01(1575136460)                        
0a.10.2   sz-3240-01(1575136460)    Pool0  LXW72ZGM              sz-3240-01(1575136460)                        
0b.10.5   sz-3240-01(1575136460)    Pool0  LXW1W02M              sz-3240-01(1575136460)                        
0b.10.11  sz-3240-01(1575136460)    Pool0  LXW6364M              sz-3240-01(1575136460)                        
0a.10.8   sz-3240-01(1575136460)    Pool0  LXV3HE7L              sz-3240-01(1575136460)                        
0b.10.9   sz-3240-01(1575136460)    Pool0  LXW5YNSM              sz-3240-01(1575136460)                        
0a.10.4   sz-3240-01(1575136460)    Pool0  LXWT76HL              sz-3240-01(1575136460)                        
0b.10.3   sz-3240-01(1575136460)    Pool0  LXW6ELRM              sz-3240-01(1575136460)                        
0a.10.10  sz-3240-01(1575136460)    Pool0  LXW6DTTM              sz-3240-01(1575136460)                        
0b.10.1   sz-3240-01(1575136460)    Pool0  LXW6R84M              sz-3240-01(1575136460)                        
0a.10.0   sz-3240-01(1575136460)    Pool0  LXV3GV4L              sz-3240-01(1575136460)                        
现在所有的磁盘都已经划分到现有控制器下了,接下来重新安装存储操作系统:    
*> halt    
Waiting for PIDS:  624.    
Terminated    
Uptime: 8m46s    
System halting...    
Phoenix TrustedCore(tm) Server    
Copyright 1985-2006 Phoenix Technologies Ltd.    
All Rights Reserved    
BIOS version: 5.3.0    
Portions Copyright (c) 2007-2014 NetApp, Inc. All Rights Reserved

CPU = 1 Processors Detected, Cores per Processor = 4  
Intel(R) Xeon(R) CPU           L5410  @ 2.33GHz    
Testing RAM    
512MB RAM tested    
8192MB RAM installed    
6144 KB L2 Cache    
System BIOS shadowed    
USB 2.0: MICRON eUSB DISK    
BIOS is scanning PCI Option ROMs, this may take a few seconds...    
+++++++++++++++++++    
Boot Loader version 3.6    
Copyright (C) 2000-2003 Broadcom Corporation.    
Portions Copyright (C) 2002-2014 NetApp, Inc. All Rights Reserved.    
CPU Type: Intel(R) Xeon(R) CPU           L5410  @ 2.33GHz    
机器起来后,要手工启动存储的系统:    
LOADER-A> boot_ontap    
Loading X86_64/freebsd/p_w_picpath2/kernel:0x200000/10088648 0xb9f0c8/4301024 Entry at 0x80271e20    
Loading X86_64/freebsd/p_w_picpath2/platform.ko:0xfba000/1990365 0x11a0000/296352 0x11e85a0/273360    
Starting program at 0x80271e20    
NetApp Data ONTAP 8.3.1P2    
Copyright (C) 1992-2015 NetApp.    
All rights reserved.    
*******************************    
*                             *    
* Press Ctrl-C for Boot Menu. *    
*                             *    
*******************************     
^CBoot Menu will be available.

WARNING:  The battery is unfit to retain data during a power  
          outage.  This is likely because the battery is    
          discharged but could be due to other temporary    
          conditions.    
          When the battery is ready, the boot process will    
          complete and services will be engaged.    
          To override this delay, press 'c' followed by 'Enter'    
c

CAUTION: Using this appliance without NVRAM  
         battery backup coupled with a power    
         failure condition CAN CAUSE DATA LOSS.    
Are you sure you want to continue (y or n)? y    
Proceeding without NVRAM battery backup.

Please choose one of the following:

(1) Normal Boot.  
(2) Boot without /etc/rc.    
(3) Change password.    
(4) Clean configuration and initialize all disks.    
(5) Maintenance mode boot.    
(6) Update flash from backup config.    
(7) Install new software first.    
(8) Reboot node.    
Selection (1-8)? 4    
ixgbe: e1a: ** JUMBOMBUF DEBUG ** switching to large buffers(9k -> 3k): (sz = 5120)!    
ixgbe: e1b: ** JUMBOMBUF DEBUG ** switching to large buffers(9k -> 3k): (sz = 5120)!    
ixgbe: e2a: ** JUMBOMBUF DEBUG ** switching to large buffers(9k -> 3k): (sz = 5120)!    
ixgbe: e2b: ** JUMBOMBUF DEBUG ** switching to large buffers(9k -> 3k): (sz = 5120)!    
Ipspace "iwarp-ipspace" created    
WAFL CPLEDGER is enabled. Checklist = 0x7ff841ff    
add host 127.0.10.1: gateway 127.0.20.1    
Zero disks, reset config and install a new file system?:    
Please answer yes or no    
Zero disks, reset config and install a new file system?: yes    
This will erase all the data on the disks, are you sure?: y    
Rebooting to finish wipeconfig request.    
Waiting for PIDS:  615.    
Skipped backing up /var file system to CF.    
Terminated    
.    
Uptime: 3m13s    
System rebooting...

Phoenix TrustedCore(tm) Server    
Copyright 1985-2006 Phoenix Technologies Ltd.    
All Rights Reserved    
BIOS version: 5.3.0    
Portions Copyright (c) 2007-2014 NetApp, Inc. All Rights Reserved

CPU = 1 Processors Detected, Cores per Processor = 4  
Intel(R) Xeon(R) CPU           L5410  @ 2.33GHz    
Testing RAM    
512MB RAM tested    
8192MB RAM installed    
6144 KB L2 Cache    
System BIOS shadowed    
USB 2.0: MICRON eUSB DISK    
BIOS is scanning PCI Option ROMs, this may take a few seconds...    
+++++++++++++++++++    
Boot Loader version 3.6    
Copyright (C) 2000-2003 Broadcom Corporation.    
Portions Copyright (C) 2002-2014 NetApp, Inc. All Rights Reserved.

CPU Type: Intel(R) Xeon(R) CPU           L5410  @ 2.33GHz

Starting AUTOBOOT press Ctrl-C to abort...  
Loading X86_64/freebsd/p_w_picpath2/kernel:0x200000/10088648 0xb9f0c8/4301024 Entry at 0x80271e20    
Loading X86_64/freebsd/p_w_picpath2/platform.ko:0xfba000/1990365 0x11a0000/296352 0x11e85a0/273360    
Starting program at 0x80271e20    
NetApp Data ONTAP 8.3.1P2    
Copyright (C) 1992-2015 NetApp.    
All rights reserved.    
*******************************    
*                             *    
* Press Ctrl-C for Boot Menu. *    
*                             *    
*******************************     
Wipe filer procedure requested.

WARNING:  The battery is unfit to retain data during a power  
          outage.  This is likely because the battery is    
          discharged but could be due to other temporary    
          conditions.    
          When the battery is ready, the boot process will    
          complete and services will be engaged.    
          To override this delay, press 'c' followed by 'Enter'    
c

CAUTION: Using this appliance without NVRAM  
         battery backup coupled with a power    
         failure condition CAN CAUSE DATA LOSS.    
Are you sure you want to continue (y or n)? y    
Proceeding without NVRAM battery backup.    
ixgbe: e1a: ** JUMBOMBUF DEBUG ** switching to large buffers(9k -> 3k): (sz = 5120)!    
ixgbe: e1b: ** JUMBOMBUF DEBUG ** switching to large buffers(9k -> 3k): (sz = 5120)!    
ixgbe: e2a: ** JUMBOMBUF DEBUG ** switching to large buffers(9k -> 3k): (sz = 5120)!    
ixgbe: e2b: ** JUMBOMBUF DEBUG ** switching to large buffers(9k -> 3k): (sz = 5120)!    
original max threads=40, original heap size=41943040    
bip_nitro Virtual Size Limit=80844390 Bytes    
bip_nitro: user memory=742682624, actual max threads=42, actual heap size=44459622    
Ipspace "iwarp-ipspace" created    
WAFL CPLEDGER is enabled. Checklist = 0x7ff841ff    
add host 127.0.10.1bootarg.bootmenu.selection is |4a|    
: gateway 127.0.20.1    
..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................    
接下来就漫长的等待了,初始化的时候是所有的硬盘同时做条带化,与硬盘数目多少无关,只与硬盘容量和转数相关。    
重启完成后,就会进入到初始化配置界面,包括集群设置、IP地址设置等等(后面会介绍,尽情期待)

推荐阅读:
  1. PowerChute远程关闭NetApp存储设定
  2. NetApp 7MTT 工具进行存储数据的迁移

免责声明:本站发布的内容(图片、视频和文字)以原创、转载和分享为主,文章观点不代表本网站立场,如果涉及侵权请联系站长邮箱:is@yisu.com进行举报,并提供相关证据,一经查实,将立刻删除涉嫌侵权内容。

控制器 windows7 color

上一篇:shell 简单计算器

下一篇:Docker入门与应用实战之容器网络

相关阅读

您好,登录后才能下订单哦!

密码登录
登录注册
其他方式登录
点击 登录注册 即表示同意《亿速云用户服务条款》