您好，登录后才能下订单哦！
密码登录
登录注册
点击 登录注册 即表示同意《亿速云用户服务条款》
之前发布了一篇《Oracle_lhr_RAC 12cR1安装》，但是其中的存储并没有使用多路径，而是使用了VMware自身提供的存储。所以，年前最后一件事就是把多路径学习一下，本文介绍了OpenFiler、iSCSI和多路径的配置。
本文内容：
OpenFile是在rPath Linux基础上开发的，它能够作为一个独立的Linux操作系统发行。Openfiler是一款非常好的存储管理操作系统，开源免费，通过web界面对存储磁盘的管理，支持现在流行的网络存储技术IP-SAN和NAS，支持iSCSI、NFS、SMB/CIFS及FTP等协议。
本次安装OpenFiler锁需要的软件如下所示：
|
序号 |
类型 |
内容 |
|
1 |
openfiler |
openfileresa-2.99.1-x86_64-disc1.iso |
注：这些软件小麦苗已上传到腾讯微云（http://blog.itpub.net/26736162/viewspace-1624453/），各位朋友可以去下载。另外，小麦苗已经将安装好的虚拟机上传到了云盘，里边已集成了rlwrap软件。
详细安装过程小麦苗就不一个一个截图了，网上已经有网友贴出了一步一步的过程，OpenFiler的内存设置为1G大小或再小点也无所谓，磁盘选用IDE磁盘格式，由于后续要配置多路径，所以需要安装2块网卡。安装完成后，重新启动，界面如下所示：
注意，方框中的内容，可以在浏览器中直接打开。可以用root用户登录进行用户的维护，若进行存储的维护则只能使用openfiler用户。openfiler是在远程使用Web界面进行管理的，小麦苗这里的管理地址是https://192.168.59.200:446，其管理的初始用户名是openfiler（小写的），密码是password，可以在登录之后，修改这个密码。
配置静态网卡地址：
|
[root@OFLHR ~]# more /etc/sysconfig/network-scripts/ifcfg-eth0 # Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] DEVICE=eth0 BOOTPROTO=static BROADCAST=192.168.59.255 HWADDR=00:0C:29:98:1A:CD IPADDR=192.168.59.200 NETMASK=255.255.255.0 NETWORK=192.168.59.0 ONBOOT=yes [root@OFLHR ~]# more /etc/sysconfig/network-scripts/ifcfg-eth2 DEVICE=eth2 MTU=1500 USERCTL=no ONBOOT=yes BOOTPROTO=static IPADDR=192.168.2.200 NETMASK=255.255.255.0 HWADDR=00:0C:29:98:1A:D7 [root@OFLHR ~]# ip a 1: lo: mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:0c:29:98:1a:cd brd ff:ff:ff:ff:ff:ff inet 192.168.59.200/24 brd 192.168.59.255 scope global eth0 inet6 fe80::20c:29ff:fe98:1acd/64 scope link valid_lft forever preferred_lft forever 3: eth2: mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:0c:29:98:1a:d7 brd ff:ff:ff:ff:ff:ff inet 192.168.2.200/24 brd 192.168.2.255 scope global eth2 inet6 fe80::20c:29ff:fe98:1ad7/64 scope link valid_lft forever preferred_lft forever [root@OFLHR ~]#
|
添加一块100G大小的IDE格式的硬盘作为存储。
|
[root@OFLHR ~]# fdisk -l
Disk /dev/sda: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders, total 20971520 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000adc2c
Device Boot Start End Blocks Id System /dev/sda1 * 63 610469 305203+ 83 Linux /dev/sda2 610470 17382329 8385930 83 Linux /dev/sda3 17382330 19486844 1052257+ 82 Linux swap / Solaris
Disk /dev/sdb: 107.4 GB, 107374182400 bytes 255 heads, 63 sectors/track, 13054 cylinders, total 209715200 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000
Disk /dev/sdb doesn't contain a valid partition table [root@OFLHR ~]#
|
为openfiler服务器配置了两块硬盘，其中10GB的硬盘已经用来安装openfiler操作系统，而200GB的硬盘则会用做数据存储。
登录地址：https://192.168.59.200:446
初始用户名和密码：openfiler/password
在独立存储设备中，LUN（Logical Unit Number）是最重要的基本单位。LUN可以被SAN中的任何主机访问，不管是透过HBA或是iSCSI。就算是软件激活的iSCSI，也可以在不同的操作系统之下，在操作系统启动之后利用软件的iSCSI initiator访问LUN。在OpenFiler之下，LUN被称为Logical Volume（LV），因此在OpenFiler下创建LUN就是创建LV。
当你安装好OpenFiler之后，接下来就是要将OpenFiler下的磁盘分享出来给虚拟机或网络上的其他主机使用了。在标准的SAN之后，这些可以在RAID层面完成，但VG的好处及弹性是RAID无法比较的，下面看看OpenFiler下的VG是如何一步一步创建的。
创建VG的步骤：
（1）进入OpenFiler的接口，并且选择要使用的实体硬盘。
（2）将要加入的实体硬盘格式化成Physical Volume格式。
（3）创建一个VG组，并且将格式化成为PV格式的实体硬盘加入。
（4）加入完毕之后，就成为一个大的VG组，被视为系统的一个大实体硬盘。
（5）在这个VG中添加逻辑分割区LUN，在OpenFiler中称为Logical Volume。
（6）指定LUN的文件格式，如iSCSI、ext3或是NFS，并且格式化。
（7）如果是iSCSI则需要再配置，如果是其他文件格式，就可以用NAS的方式分享出去而
登录后，点击Volumes标签
为openfiler服务器配置了两块硬盘，其中10GB的硬盘已经用来安装openfiler操作系统，而200GB的硬盘则会用做数据存储。
点击create new physical volumes后点击/dev/sdb
点击页面右下角Reset，然后点击Create。分区类型为Physical volume
点击Volume Groups
输入名称，勾选复选框，单击Add volume group
|
[root@OFLHR ~]# fdisk -l
Disk /dev/sda: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders, total 20971520 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000adc2c
Device Boot Start End Blocks Id System /dev/sda1 * 63 610469 305203+ 83 Linux /dev/sda2 610470 17382329 8385930 83 Linux /dev/sda3 17382330 19486844 1052257+ 82 Linux swap / Solaris
WARNING: GPT (GUID Partition Table) detected on '/dev/sdb'! The util fdisk doesn't support GPT. Use GNU Parted.
Disk /dev/sdb: 107.4 GB, 107374182400 bytes 255 heads, 63 sectors/track, 13054 cylinders, total 209715200 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000
Device Boot Start End Blocks Id System /dev/sdb1 1 209715199 104857599+ ee GPT [root@OFLHR ~]# pvs PV VG Fmt Attr PSize PFree /dev/sdb1 vmlhr lvm2 a- 95.34g 95.34g [root@OFLHR ~]#
|
点击Add Volume
输入内容，调整磁盘大小为10G，卷类型选择block（iSCSI，FC，etc）
依次共创建4个逻辑卷：
|
[root@OFLHR ~]# vgs VG #PV #LV #SN Attr VSize VFree vmlhr 1 4 0 wz--n- 95.34g 55.34g [root@OFLHR ~]# pvs PV VG Fmt Attr PSize PFree /dev/sdb1 vmlhr lvm2 a- 95.34g 55.34g [root@OFLHR ~]# lvs LV VG Attr LSize Origin Snap% Move Log Copy% Convert lv01 vmlhr -wi-a- 10.00g lv02 vmlhr -wi-a- 10.00g lv03 vmlhr -wi-a- 10.00g lv04 vmlhr -wi-a- 10.00g [root@OFLHR ~]# fdisk -l
Disk /dev/sda: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders, total 20971520 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000adc2c
Device Boot Start End Blocks Id System /dev/sda1 * 63 610469 305203+ 83 Linux /dev/sda2 610470 17382329 8385930 83 Linux /dev/sda3 17382330 19486844 1052257+ 82 Linux swap / Solaris
WARNING: GPT (GUID Partition Table) detected on '/dev/sdb'! The util fdisk doesn't support GPT. Use GNU Parted.
Disk /dev/sdb: 107.4 GB, 107374182400 bytes 255 heads, 63 sectors/track, 13054 cylinders, total 209715200 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000
Device Boot Start End Blocks Id System /dev/sdb1 1 209715199 104857599+ ee GPT
Disk /dev/dm-0: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders, total 20971520 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000
Disk /dev/dm-0 doesn't contain a valid partition table
Disk /dev/dm-1: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders, total 20971520 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000
Disk /dev/dm-1 doesn't contain a valid partition table
Disk /dev/dm-2: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders, total 20971520 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000
Disk /dev/dm-2 doesn't contain a valid partition table
Disk /dev/dm-3: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders, total 20971520 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000
Disk /dev/dm-3 doesn't contain a valid partition table [root@OFLHR ~]#
|
点击Services标签栏设置iSCSI Target 为Enable 开启服务Start。
返回Volumes标签页，点击iSCSI Targets
点击Add
选择LUN Mapping标签 点击Map
由于iSCSI是走IP网络，因此我们要允许网络中的计算机可以透过IP来访问。下面就是OpenFiler中IP网络和同一网段中其他主机的连接方法。
1．进入OpenFiler中的System，并且直接拉到页面的下方。
2．在Network Access Configuration的地方输入这个网络访问的名称，如VM_LHR。
3．输入主机的IP段。注意不可以输入单一主机的IP，这样会都无法访问。我们在这边输入192.168.59.0，表示从192.168.59.1一直到192.168.59.254都能访问。
4．在Netmask中选择255.255.255.0，并且在Type下拉列表框中选择Share，之后即可以单击Update按钮。
选择完之后就更新
至此就可以在这个OpenFiler中看到被授权的网段了。
在iSCSI Targets中，点击 Network ACL 标签
设置Access为Allow 然后点击Update
到此存储的配置已经完成
注释掉iqn.2006-01.com.openfiler:tsn.5e423e1e4d90 ALL：
|
[root@OFLHR ~]# more /etc/initiators.deny
# PLEASE DO NOT MODIFY THIS CONFIGURATION FILE! # This configuration file was autogenerated # by Openfiler. Any manual changes will be overwritten # Generated at: Sat Jan 21 1:49:55 CST 2017
#iqn.2006-01.com.openfiler:tsn.5e423e1e4d90 ALL
# End of Openfiler configuration
[root@OFLHR ~]#
|
iSCSI（Internet Small Computer System Interface）。iSCSI技术由IBM公司研究开发，是一个供硬件设备使用的、可以在IP协议的上层运行的SCSI指令集，这种指令集合可以实现在IP网络上运行SCSI协议，使其能够在诸如高速千兆以太网上进行路由选择。iSCSI技术是一种新储存技术，该技术是将现有SCSI接口与以太网络(Ethernet)技术结合，使服务器可与使用IP网络的储存装置互相交换资料。iSCSI是一种基于 TCP/IP 的协议，用来建立和管理 IP存储设备、主机和客户机等之间的相互连接，并创建存储区域网络（SAN）。
iSCSI target：就是储存设备端，存放磁盘或RAID的设备，目前也能够将Linux主机模拟成iSCSI target了！目的在提供其他主机使用的『磁盘』；
iSCSI initiator：就是能够使用target的用户端，通常是服务器。也就是说，想要连接到iSCSI target的服务器，也必须要安装iSCSI initiator的相关功能后才能够使用iSCSI target提供的磁盘。
|
[root@OFLHR ~]# service iscsi-target start Starting iSCSI target service: [ OK ] [root@OFLHR ~]# more /etc/ietd.conf ##### WARNING!!! - This configuration file generated by Openfiler. DO NOT MANUALLY EDIT. #####
Target iqn.2006-01.com.openfiler:tsn.5e423e1e4d90 HeaderDigest None DataDigest None MaxConnections 1 InitialR2T Yes ImmediateData No MaxRecvDataSegmentLength 131072 MaxXmitDataSegmentLength 131072 MaxBurstLength 262144 FirstBurstLength 262144 DefaultTime2Wait 2 DefaultTime2Retain 20 MaxOutstandingR2T 8 DataPDUInOrder Yes DataSequenceInOrder Yes ErrorRecoveryLevel 0 Lun 0 Path=/dev/vmlhr/lv01,Type=blockio,ScsiSN=22llvD-CacO-MOMA,ScsiId=22llvD-CacO-MOMA,IOMode=wt Lun 1 Path=/dev/vmlhr/lv02,Type=blockio,ScsiSN=BgLpy9-u7PH-csDC,ScsiId=BgLpy9-u7PH-csDC,IOMode=wt Lun 2 Path=/dev/vmlhr/lv03,Type=blockio,ScsiSN=38KsSC-REKL-yPgW,ScsiId=38KsSC-REKL-yPgW,IOMode=wt Lun 3 Path=/dev/vmlhr/lv04,Type=blockio,ScsiSN=aN5blo-NyMp-L4Jl,ScsiId=aN5blo-NyMp-L4Jl,IOMode=wt
[root@OFLHR ~]# ps -ef|grep iscsi root 937 2 0 01:01 ? 00:00:00 [iscsi_eh] root 946 1 0 01:01 ? 00:00:00 iscsid root 947 1 0 01:01 ? 00:00:00 iscsid root 13827 1217 0 02:43 pts/1 00:00:00 grep iscsi [root@OFLHR ~]# cat /proc/net/iet/volume tid:1 name:iqn.2006-01.com.openfiler:tsn.5e423e1e4d90 lun:0 state:0 iotype:blockio iomode:wt path:/dev/vmlhr/lv01 lun:1 state:0 iotype:blockio iomode:wt path:/dev/vmlhr/lv02 lun:2 state:0 iotype:blockio iomode:wt path:/dev/vmlhr/lv03 lun:3 state:0 iotype:blockio iomode:wt path:/dev/vmlhr/lv04 [root@OFLHR ~]# cat /proc/net/iet/session tid:1 name:iqn.2006-01.com.openfiler:tsn.5e423e1e4d90 [root@OFLHR ~]#
|
RAC的2个节点分别安装iSCSI initiator。
|
[root@raclhr-12cR1-N1 ~]# rpm -qa|grep iscsi iscsi-initiator-utils-6.2.0.873-10.el6.x86_64 [root@raclhr-12cR1-N1 ~]#
|
若未安装可使用yum install iscsi-initiator-utils*进行安装。
iscsi initiator主要通过iscsiadm命令管理，我们先查看提供服务的iscsi target机器上有哪些target:
|
[root@raclhr-12cR1-N1 ~]# iscsiadm --mode discovery --type sendtargets --portal 192.168.59.200 [ OK ] iscsid: [ OK ] 192.168.59.200:3260,1 iqn.2006-01.com.openfiler:tsn.5e423e1e4d90 192.168.2.200:3260,1 iqn.2006-01.com.openfiler:tsn.5e423e1e4d90 [root@raclhr-12cR1-N1 ~]# ps -ef|grep iscsi root 2619 2 0 11:32 ? 00:00:00 [iscsi_eh] root 2651 1 0 11:32 ? 00:00:00 iscsiuio root 2658 1 0 11:32 ? 00:00:00 iscsid root 2659 1 0 11:32 ? 00:00:00 iscsid root 2978 56098 0 11:33 pts/1 00:00:00 grep iscsi [root@raclhr-12cR1-N1 ~]#
|
到这一步就可以看出，你服务端创建的iSCSI Target 的编号和名称。这条命令只需记住-p后面跟iSCSI服务的地址就行了，也可以是主机名，都可以！3260是服务的端口号，默认的！
然后就可以登陆某个target了，登陆成功某个target后，这个target下的硬盘也就都共享过来了：
|
[root@raclhr-12cR1-N1 ~]# fdisk -l | grep dev Disk /dev/sda: 21.5 GB, 21474836480 bytes /dev/sda1 * 1 26 204800 83 Linux /dev/sda2 26 1332 10485760 8e Linux LVM /dev/sda3 1332 2611 10279936 8e Linux LVM Disk /dev/sdb: 107.4 GB, 107374182400 bytes /dev/sdb1 1 1306 10485760 8e Linux LVM /dev/sdb2 1306 2611 10485760 8e Linux LVM /dev/sdb3 2611 3917 10485760 8e Linux LVM /dev/sdb4 3917 13055 73399296 5 Extended /dev/sdb5 3917 5222 10485760 8e Linux LVM /dev/sdb6 5223 6528 10485760 8e Linux LVM /dev/sdb7 6528 7834 10485760 8e Linux LVM /dev/sdb8 7834 9139 10485760 8e Linux LVM /dev/sdb9 9139 10445 10485760 8e Linux LVM /dev/sdb10 10445 11750 10485760 8e Linux LVM /dev/sdb11 11750 13055 10477568 8e Linux LVM Disk /dev/sde: 10.7 GB, 10737418240 bytes Disk /dev/sdc: 6442 MB, 6442450944 bytes Disk /dev/sdd: 10.7 GB, 10737418240 bytes Disk /dev/mapper/vg_rootlhr-Vol02: 2147 MB, 2147483648 bytes Disk /dev/mapper/vg_rootlhr-Vol00: 10.7 GB, 10737418240 bytes Disk /dev/mapper/vg_orasoft-lv_orasoft_u01: 21.5 GB, 21474836480 bytes Disk /dev/mapper/vg_orasoft-lv_orasoft_soft: 21.5 GB, 21474836480 bytes Disk /dev/mapper/vg_rootlhr-Vol01: 3221 MB, 3221225472 bytes Disk /dev/mapper/vg_rootlhr-Vol03: 3221 MB, 3221225472 bytes [root@raclhr-12cR1-N1 ~]# iscsiadm --mode node --targetname iqn.2006-01.com.openfiler:tsn.5e423e1e4d90 –portal 192.168.59.200:3260 --login Logging in to [iface: default, target: iqn.2006-01.com.openfiler:tsn.5e423e1e4d90, portal: 192.168.59.200,3260] (multiple) Logging in to [iface: default, target: iqn.2006-01.com.openfiler:tsn.5e423e1e4d90, portal: 192.168.2.200,3260] (multiple) Login to [iface: default, target: iqn.2006-01.com.openfiler:tsn.5e423e1e4d90, portal: 192.168.59.200,3260] successful. Login to [iface: default, target: iqn.2006-01.com.openfiler:tsn.5e423e1e4d90, portal: 192.168.2.200,3260] successful. [root@raclhr-12cR1-N1 ~]# [root@raclhr-12cR1-N1 ~]# fdisk -l | grep dev Disk /dev/sda: 21.5 GB, 21474836480 bytes /dev/sda1 * 1 26 204800 83 Linux /dev/sda2 26 1332 10485760 8e Linux LVM /dev/sda3 1332 2611 10279936 8e Linux LVM Disk /dev/sdb: 107.4 GB, 107374182400 bytes /dev/sdb1 1 1306 10485760 8e Linux LVM /dev/sdb2 1306 2611 10485760 8e Linux LVM /dev/sdb3 2611 3917 10485760 8e Linux LVM /dev/sdb4 3917 13055 73399296 5 Extended /dev/sdb5 3917 5222 10485760 8e Linux LVM /dev/sdb6 5223 6528 10485760 8e Linux LVM /dev/sdb7 6528 7834 10485760 8e Linux LVM /dev/sdb8 7834 9139 10485760 8e Linux LVM /dev/sdb9 9139 10445 10485760 8e Linux LVM /dev/sdb10 10445 11750 10485760 8e Linux LVM /dev/sdb11 11750 13055 10477568 8e Linux LVM Disk /dev/sde: 10.7 GB, 10737418240 bytes Disk /dev/sdc: 6442 MB, 6442450944 bytes Disk /dev/sdd: 10.7 GB, 10737418240 bytes Disk /dev/mapper/vg_rootlhr-Vol02: 2147 MB, 2147483648 bytes Disk /dev/mapper/vg_rootlhr-Vol00: 10.7 GB, 10737418240 bytes Disk /dev/mapper/vg_orasoft-lv_orasoft_u01: 21.5 GB, 21474836480 bytes Disk /dev/mapper/vg_orasoft-lv_orasoft_soft: 21.5 GB, 21474836480 bytes Disk /dev/mapper/vg_rootlhr-Vol01: 3221 MB, 3221225472 bytes Disk /dev/mapper/vg_rootlhr-Vol03: 3221 MB, 3221225472 bytes Disk /dev/sdf: 10.7 GB, 10737418240 bytes Disk /dev/sdi: 10.7 GB, 10737418240 bytes Disk /dev/sdh: 10.7 GB, 10737418240 bytes Disk /dev/sdl: 10.7 GB, 10737418240 bytes Disk /dev/sdj: 10.7 GB, 10737418240 bytes Disk /dev/sdg: 10.7 GB, 10737418240 bytes Disk /dev/sdk: 10.7 GB, 10737418240 bytes Disk /dev/sdm: 10.7 GB, 10737418240 bytes
|
这里多出了8块盘，在openfiler中只map了四次，为什么这里是8块而不是4块呢？因为openfiler有2块网卡，使用两个IP登录两次iscsi target，所以这里有两块是重复的
要查看各个iscsi的信息：
# iscsiadm -m session -P 3
|
[root@raclhr-12cR1-N1 ~]# [root@raclhr-12cR1-N1 ~]# iscsiadm -m session -P 3 iSCSI Transport Class version 2.0-870 version 6.2.0-873.10.el6 Target: iqn.2006-01.com.openfiler:tsn.5e423e1e4d90 Current Portal: 192.168.59.200:3260,1 Persistent Portal: 192.168.59.200:3260,1 ********** Interface: ********** Iface Name: default Iface Transport: tcp Iface Initiatorname: iqn.1994-05.com.redhat:61d32512355 Iface IPaddress: 192.168.59.160 Iface HWaddress: Iface Netdev: SID: 1 iSCSI Connection State: LOGGED IN iSCSI Session State: LOGGED_IN Internal iscsid Session State: NO CHANGE ********* Timeouts: ********* Recovery Timeout: 120 Target Reset Timeout: 30 LUN Reset Timeout: 30 Abort Timeout: 15 ***** CHAP: ***** username: password: ******** username_in: password_in: ******** ************************ Negotiated iSCSI params: ************************ HeaderDigest: None DataDigest: None MaxRecvDataSegmentLength: 262144 MaxXmitDataSegmentLength: 131072 FirstBurstLength: 262144 MaxBurstLength: 262144 ImmediateData: No InitialR2T: Yes MaxOutstandingR2T: 1 ************************ Attached SCSI devices: ************************ Host Number: 4 State: running scsi4 Channel 00 Id 0 Lun: 0 Attached scsi disk sdg State: running scsi4 Channel 00 Id 0 Lun: 1 Attached scsi disk sdj State: running scsi4 Channel 00 Id 0 Lun: 2 Attached scsi disk sdk State: running scsi4 Channel 00 Id 0 Lun: 3 Attached scsi disk sdm State: running Current Portal: 192.168.2.200:3260,1 Persistent Portal: 192.168.2.200:3260,1 ********** Interface: ********** Iface Name: default Iface Transport: tcp Iface Initiatorname: iqn.1994-05.com.redhat:61d32512355 Iface IPaddress: 192.168.2.100 Iface HWaddress: Iface Netdev: SID: 2 iSCSI Connection State: LOGGED IN iSCSI Session State: LOGGED_IN Internal iscsid Session State: NO CHANGE ********* Timeouts: ********* Recovery Timeout: 120 Target Reset Timeout: 30 LUN Reset Timeout: 30 Abort Timeout: 15 ***** CHAP: ***** username: password: ******** username_in: password_in: ******** ************************ Negotiated iSCSI params: ************************ HeaderDigest: None DataDigest: None MaxRecvDataSegmentLength: 262144 MaxXmitDataSegmentLength: 131072 FirstBurstLength: 262144 MaxBurstLength: 262144 ImmediateData: No InitialR2T: Yes MaxOutstandingR2T: 1 ************************ Attached SCSI devices: ************************ Host Number: 5 State: running scsi5 Channel 00 Id 0 Lun: 0 Attached scsi disk sdf State: running scsi5 Channel 00 Id 0 Lun: 1 Attached scsi disk sdh State: running scsi5 Channel 00 Id 0 Lun: 2 Attached scsi disk sdi State: running scsi5 Channel 00 Id 0 Lun: 3 Attached scsi disk sdl State: running [root@raclhr-12cR1-N1 ~]#
|
登陆之后要对新磁盘进行分区，格式化，然后在挂载即可
完成这些命令后，iscsi initator会把这些信息记录到/var/lib/iscsi目录下：
/var/lib/iscsi/send_targets记录了各个target的情况，/var/lib/iscsi/nodes记录了各个target下的nodes情况。下次再启动iscsi initator时（service iscsi start)，就会自动登陆各个target上。如果想让重新手工登陆各个target，需要把/var/lib/iscsi/send_targets目录下的内容和/var/lib/iscsi/nodes下的内容全部删除掉。
1、安装多路径软件包：
|
[root@raclhr-12cR1-N1 ~]# mount /dev/sr0 /media/lhr/cdrom/ mount: block device /dev/sr0 is write-protected, mounting read-only [root@raclhr-12cR1-N1 ~]# cd /media/lhr/cdrom/Packages/ [root@raclhr-12cR1-N1 Packages]# ll device-mapper-*.x86_64.rpm -r--r--r-- 104 root root 168424 Oct 30 2013 device-mapper-1.02.79-8.el6.x86_64.rpm -r--r--r-- 104 root root 118316 Oct 30 2013 device-mapper-event-1.02.79-8.el6.x86_64.rpm -r--r--r-- 104 root root 112892 Oct 30 2013 device-mapper-event-libs-1.02.79-8.el6.x86_64.rpm -r--r--r-- 104 root root 199924 Oct 30 2013 device-mapper-libs-1.02.79-8.el6.x86_64.rpm -r--r--r-- 95 root root 118892 Oct 25 2013 device-mapper-multipath-0.4.9-72.el6.x86_64.rpm -r--r--r-- 95 root root 184760 Oct 25 2013 device-mapper-multipath-libs-0.4.9-72.el6.x86_64.rpm -r--r--r-- 96 root root 2444388 Oct 30 2013 device-mapper-persistent-data-0.2.8-2.el6.x86_64.rpm [root@raclhr-12cR1-N1 Packages]# ll iscsi* -r--r--r-- 101 root root 702300 Oct 29 2013 iscsi-initiator-utils-6.2.0.873-10.el6.x86_64.rpm [root@raclhr-12cR1-N1 Packages]# rpm -qa|grep device-mapper device-mapper-persistent-data-0.2.8-2.el6.x86_64 device-mapper-1.02.79-8.el6.x86_64 device-mapper-event-libs-1.02.79-8.el6.x86_64 device-mapper-event-1.02.79-8.el6.x86_64 device-mapper-libs-1.02.79-8.el6.x86_64 [root@raclhr-12cR1-N1 Packages]# rpm -ivh device-mapper-1.02.79-8.el6.x86_64.rpm warning: device-mapper-1.02.79-8.el6.x86_64.rpm: Header V3 RSA/SHA256 Signature, key ID fd431d51: NOKEY Preparing... ########################################### [100%] package device-mapper-1.02.79-8.el6.x86_64 is already installed [root@raclhr-12cR1-N1 Packages]# rpm -ivh device-mapper-event-1.02.79-8.el6.x86_64.rpm warning: device-mapper-event-1.02.79-8.el6.x86_64.rpm: Header V3 RSA/SHA256 Signature, key ID fd431d51: NOKEY Preparing... ########################################### [100%] package device-mapper-event-1.02.79-8.el6.x86_64 is already installed [root@raclhr-12cR1-N1 Packages]# rpm -ivh device-mapper-multipath-0.4.9-72.el6.x86_64.rpm warning: device-mapper-multipath-0.4.9-72.el6.x86_64.rpm: Header V3 RSA/SHA256 Signature, key ID fd431d51: NOKEY error: Failed dependencies: device-mapper-multipath-libs = 0.4.9-72.el6 is needed by device-mapper-multipath-0.4.9-72.el6.x86_64 libmpathpersist.so.0()(64bit) is needed by device-mapper-multipath-0.4.9-72.el6.x86_64 libmultipath.so()(64bit) is needed by device-mapper-multipath-0.4.9-72.el6.x86_64 [root@raclhr-12cR1-N1 Packages]# rpm -ivh device-mapper-multipath-libs-0.4.9-72.el6.x86_64.rpm warning: device-mapper-multipath-libs-0.4.9-72.el6.x86_64.rpm: Header V3 RSA/SHA256 Signature, key ID fd431d51: NOKEY Preparing... ########################################### [100%] 1:device-mapper-multipath########################################### [100%] [root@raclhr-12cR1-N1 Packages]# rpm -ivh device-mapper-multipath-0.4.9-72.el6.x86_64.rpm warning: device-mapper-multipath-0.4.9-72.el6.x86_64.rpm: Header V3 RSA/SHA256 Signature, key ID fd431d51: NOKEY Preparing... ########################################### [100%] 1:device-mapper-multipath########################################### [100%] [root@raclhr-12cR1-N1 Packages]# rpm -qa|grep device-mapper device-mapper-multipath-0.4.9-72.el6.x86_64 device-mapper-persistent-data-0.2.8-2.el6.x86_64 device-mapper-1.02.79-8.el6.x86_64 device-mapper-event-libs-1.02.79-8.el6.x86_64 device-mapper-event-1.02.79-8.el6.x86_64 device-mapper-multipath-libs-0.4.9-72.el6.x86_64 device-mapper-libs-1.02.79-8.el6.x86_64 [root@raclhr-12cR1-N2 Packages]#
|
|
rpm -ivh device-mapper-multipath-libs-0.4.9-72.el6.x86_64.rpm rpm -ivh device-mapper-multipath-0.4.9-72.el6.x86_64.rpm
|
将多路径软件添加至内核模块中
|
modprobe dm-multipath modprobe dm-round-robin
|
检查内核添加情况
|
[root@raclhr-12cR1-N1 Packages]# lsmod |grep multipath dm_multipath 17724 1 dm_round_robin dm_mod 84209 16 dm_multipath,dm_mirror,dm_log [root@raclhr-12cR1-N1 Packages]# |
将多路径软件multipath设置为开机自启动
|
[root@raclhr-12cR1-N1 Packages]# chkconfig --level 2345 multipathd on [root@raclhr-12cR1-N1 Packages]# [root@raclhr-12cR1-N1 Packages]# chkconfig --list|grep multipathd multipathd 0:off 1:off 2:on 3:on 4:on 5:on 6:off [root@raclhr-12cR1-N1 Packages]# |
启动multipath服务
|
[root@raclhr-12cR1-N1 Packages]# service multipathd restart ux_socket_connect: No such file or directory Stopping multipathd daemon: [FAILED] Starting multipathd daemon: [ OK ] [root@raclhr-12cR1-N1 Packages]# |
1、配置multipath软件，编辑/etc/multipath.conf
注意:默认情况下，/etc/multipath.conf是不存在的，需要用如下命令生成multipath.conf文件:
/sbin/mpathconf --enable --find_multipaths y --with_module y --with_chkconfig y
|
[root@raclhr-12cR1-N1 ~]# multipath -ll Jan 23 12:52:54 | /etc/multipath.conf does not exist, blacklisting all devices. Jan 23 12:52:54 | A sample multipath.conf file is located at Jan 23 12:52:54 | /usr/share/doc/device-mapper-multipath-0.4.9/multipath.conf Jan 23 12:52:54 | You can run /sbin/mpathconf to create or modify /etc/multipath.conf [root@raclhr-12cR1-N1 ~]# multipath -ll Jan 23 12:53:49 | /etc/multipath.conf does not exist, blacklisting all devices. Jan 23 12:53:49 | A sample multipath.conf file is located at Jan 23 12:53:49 | /usr/share/doc/device-mapper-multipath-0.4.9/multipath.conf Jan 23 12:53:49 | You can run /sbin/mpathconf to create or modify /etc/multipath.conf [root@raclhr-12cR1-N1 ~]# /sbin/mpathconf --enable --find_multipaths y --with_module y --with_chkconfig y [root@raclhr-12cR1-N1 ~]# [root@raclhr-12cR1-N1 ~]# ll /etc/multipath.conf -rw------- 1 root root 2775 Jan 23 12:55 /etc/multipath.conf [root@raclhr-12cR1-N1 ~]#
|
2、查看并获取存储分配给服务器的逻辑盘lun的wwid信息
|
[root@raclhr-12cR1-N1 multipath]# multipath -v0 [root@raclhr-12cR1-N1 multipath]# more /etc/multipath/wwids # Multipath wwids, Version : 1.0 # NOTE: This file is automatically maintained by multipath and multipathd. # You should not need to edit this file in normal circumstances. # # Valid WWIDs: /14f504e46494c455232326c6c76442d4361634f2d4d4f4d41/ /14f504e46494c455242674c7079392d753750482d63734443/ /14f504e46494c455233384b7353432d52454b4c2d79506757/ /14f504e46494c4552614e35626c6f2d4e794d702d4c344a6c/ [root@raclhr-12cR1-N1 multipath]#
|
将文件/etc/multipath/wwids和/etc/multipath/bindings的内容覆盖节点2：
|
[root@raclhr-12cR1-N2 ~]# multipath -v0 [root@raclhr-12cR1-N2 ~]# more /etc/multipath/wwids # Multipath wwids, Version : 1.0 # NOTE: This file is automatically maintained by multipath and multipathd. # You should not need to edit this file in normal circumstances. # # Valid WWIDs: /14f504e46494c455232326c6c76442d4361634f2d4d4f4d41/ /14f504e46494c455242674c7079392d753750482d63734443/ /14f504e46494c455233384b7353432d52454b4c2d79506757/ /14f504e46494c4552614e35626c6f2d4e794d702d4c344a6c/ [root@raclhr-12cR1-N1 ~]# more /etc/multipath/bindings # Multipath bindings, Version : 1.0 # NOTE: this file is automatically maintained by the multipath program. # You should not need to edit this file in normal circumstances. # # Format: # alias wwid # mpatha 14f504e46494c455232326c6c76442d4361634f2d4d4f4d41 mpathb 14f504e46494c455242674c7079392d753750482d63734443 mpathc 14f504e46494c455233384b7353432d52454b4c2d79506757 mpathd 14f504e46494c4552614e35626c6f2d4e794d702d4c344a6c [root@raclhr-12cR1-N1 ~]#
|
|
[root@raclhr-12cR1-N2 ~]# [root@raclhr-12cR1-N1 multipath]# multipath -ll mpathd (14f504e46494c4552614e35626c6f2d4e794d702d4c344a6c) dm-9 OPNFILER,VIRTUAL-DISK size=10G features='0' hwhandler='0' wp=rw |-+- policy='round-robin 0' prio=1 status=active | `- 5:0:0:3 sdk 8:160 active ready running `-+- policy='round-robin 0' prio=1 status=enabled `- 4:0:0:3 sdm 8:192 active ready running mpathc (14f504e46494c455233384b7353432d52454b4c2d79506757) dm-8 OPNFILER,VIRTUAL-DISK size=10G features='0' hwhandler='0' wp=rw |-+- policy='round-robin 0' prio=1 status=active | `- 5:0:0:2 sdj 8:144 active ready running `-+- policy='round-robin 0' prio=1 status=enabled `- 4:0:0:2 sdl 8:176 active ready running mpathb (14f504e46494c455242674c7079392d753750482d63734443) dm-7 OPNFILER,VIRTUAL-DISK size=10G features='0' hwhandler='0' wp=rw |-+- policy='round-robin 0' prio=1 status=active | `- 4:0:0:1 sdh 8:112 active ready running `-+- policy='round-robin 0' prio=1 status=enabled `- 5:0:0:1 sdi 8:128 active ready running mpatha (14f504e46494c455232326c6c76442d4361634f2d4d4f4d41) dm-6 OPNFILER,VIRTUAL-DISK size=10G features='0' hwhandler='0' wp=rw |-+- policy='round-robin 0' prio=1 status=active | `- 4:0:0:0 sdf 8:80 active ready running `-+- policy='round-robin 0' prio=1 status=enabled `- 5:0:0:0 sdg 8:96 active ready running [root@raclhr-12cR1-N1 multipath]# fdisk -l | grep dev Disk /dev/sda: 21.5 GB, 21474836480 bytes /dev/sda1 * 1 26 204800 83 Linux /dev/sda2 26 1332 10485760 8e Linux LVM /dev/sda3 1332 2611 10279936 8e Linux LVM Disk /dev/sdb: 107.4 GB, 107374182400 bytes /dev/sdb1 1 1306 10485760 8e Linux LVM /dev/sdb2 1306 2611 10485760 8e Linux LVM /dev/sdb3 2611 3917 10485760 8e Linux LVM /dev/sdb4 3917 13055 73399296 5 Extended /dev/sdb5 3917 5222 10485760 8e Linux LVM /dev/sdb6 5223 6528 10485760 8e Linux LVM /dev/sdb7 6528 7834 10485760 8e Linux LVM /dev/sdb8 7834 9139 10485760 8e Linux LVM /dev/sdb9 9139 10445 10485760 8e Linux LVM /dev/sdb10 10445 11750 10485760 8e Linux LVM /dev/sdb11 11750 13055 10477568 8e Linux LVM Disk /dev/sdc: 6442 MB, 6442450944 bytes Disk /dev/sdd: 10.7 GB, 10737418240 bytes Disk /dev/sde: 10.7 GB, 10737418240 bytes Disk /dev/mapper/vg_rootlhr-Vol02: 2147 MB, 2147483648 bytes Disk /dev/mapper/vg_rootlhr-Vol00: 10.7 GB, 10737418240 bytes Disk /dev/mapper/vg_orasoft-lv_orasoft_u01: 21.5 GB, 21474836480 bytes Disk /dev/mapper/vg_orasoft-lv_orasoft_soft: 21.5 GB, 21474836480 bytes Disk /dev/mapper/vg_rootlhr-Vol01: 3221 MB, 3221225472 bytes Disk /dev/mapper/vg_rootlhr-Vol03: 3221 MB, 3221225472 bytes Disk /dev/sdf: 10.7 GB, 10737418240 bytes Disk /dev/sdg: 10.7 GB, 10737418240 bytes Disk /dev/sdh: 10.7 GB, 10737418240 bytes Disk /dev/sdi: 10.7 GB, 10737418240 bytes Disk /dev/sdj: 10.7 GB, 10737418240 bytes Disk /dev/sdk: 10.7 GB, 10737418240 bytes Disk /dev/sdl: 10.7 GB, 10737418240 bytes Disk /dev/sdm: 10.7 GB, 10737418240 bytes Disk /dev/mapper/mpatha: 10.7 GB, 10737418240 bytes Disk /dev/mapper/mpathb: 10.7 GB, 10737418240 bytes Disk /dev/mapper/mpathc: 10.7 GB, 10737418240 bytes Disk /dev/mapper/mpathd: 10.7 GB, 10737418240 bytes [root@raclhr-12cR1-N1 multipath]#
|
|
for i in f g h i j k l m ; do echo "KERNEL==\"sd*\", BUS==\"scsi\", PROGRAM==\"/sbin/scsi_id --whitelisted --device=/dev/\$name\",RESULT==\"`scsi_id --whitelisted --device=/dev/sd$i`\",NAME=\"asm-disk$i\",OWNER=\"grid\",GROUP=\"asmadmin\",MODE=\"0660\"" done
|
|
[root@raclhr-12cR1-N1 multipath]# for i in f g h i j k l m ; > do > echo "KERNEL==\"sd*\", BUS==\"scsi\", PROGRAM==\"/sbin/scsi_id --whitelisted --device=/dev/\$name\",RESULT==\"`scsi_id --whitelisted --device=/dev/sd$i`\",NAME=\"asm-disk$i\",OWNER=\"grid\",GROUP=\"asmadmin\",MODE=\"0660\"" > done KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --device=/dev/$name",RESULT=="14f504e46494c455232326c6c76442d4361634f2d4d4f4d41",NAME="asm-diskf",OWNER="grid",GROUP="asmadmin",MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --device=/dev/$name",RESULT=="14f504e46494c455232326c6c76442d4361634f2d4d4f4d41",NAME="asm-diskg",OWNER="grid",GROUP="asmadmin",MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --device=/dev/$name",RESULT=="14f504e46494c455242674c7079392d753750482d63734443",NAME="asm-diskh",OWNER="grid",GROUP="asmadmin",MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --device=/dev/$name",RESULT=="14f504e46494c455242674c7079392d753750482d63734443",NAME="asm-diski",OWNER="grid",GROUP="asmadmin",MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --device=/dev/$name",RESULT=="14f504e46494c455233384b7353432d52454b4c2d79506757",NAME="asm-diskj",OWNER="grid",GROUP="asmadmin",MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --device=/dev/$name",RESULT=="14f504e46494c4552614e35626c6f2d4e794d702d4c344a6c",NAME="asm-diskk",OWNER="grid",GROUP="asmadmin",MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --device=/dev/$name",RESULT=="14f504e46494c455233384b7353432d52454b4c2d79506757",NAME="asm-diskl",OWNER="grid",GROUP="asmadmin",MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --device=/dev/$name",RESULT=="14f504e46494c4552614e35626c6f2d4e794d702d4c344a6c",NAME="asm-diskm",OWNER="grid",GROUP="asmadmin",MODE="0660" [root@raclhr-12cR1-N1 multipath]# [root@raclhr-12cR1-N1 multipath]# more /etc/multipath.conf defaults { find_multipaths yes user_friendly_names yes }
blacklist { wwid 3600508b1001c5ae72efe1fea025cd2e5 devnode "^hd[a-z]" devnode "^sd[a-e]" devnode "^sda" }
multipaths { multipath { wwid 14f504e46494c455232326c6c76442d4361634f2d4d4f4d41 alias VMLHRStorage000 path_grouping_policy multibus path_selector "round-robin 0" failback manual rr_weight priorities no_path_retry 5 } multipath { wwid 14f504e46494c455242674c7079392d753750482d63734443 alias VMLHRStorage001 path_grouping_policy multibus path_selector "round-robin 0" failback manual rr_weight priorities no_path_retry 5 } multipath { wwid 14f504e46494c455233384b7353432d52454b4c2d79506757 alias VMLHRStorage002 path_grouping_policy multibus path_selector "round-robin 0" failback manual rr_weight priorities no_path_retry 5 } multipath { wwid 14f504e46494c4552614e35626c6f2d4e794d702d4c344a6c alias VMLHRStorage003 path_grouping_policy multibus path_selector "round-robin 0" failback manual rr_weight priorities no_path_retry 5 } } devices { device { vendor "VMWARE" product "VIRTUAL-DISK" path_grouping_policy multibus getuid_callout "/lib/udev/scsi_id --whitelisted --device=/dev/%n" path_checker readsector0 path_selector "round-robin 0" hardware_handler "0" failback 15 rr_weight priorities no_path_retry queue } } [root@raclhr-12cR1-N1 multipath]#
|
启动multipath配置
|
[root@raclhr-12cR1-N1 ~]# service multipathd restart ok Stopping multipathd daemon: [ OK ] Starting multipathd daemon: [ OK ] [root@raclhr-12cR1-N1 ~]# multipath -ll VMLHRStorage003 (14f504e46494c4552614e35626c6f2d4e794d702d4c344a6c) dm-9 OPNFILER,VIRTUAL-DISK size=10G features='1 queue_if_no_path' hwhandler='0' wp=rw |-+- policy='round-robin 0' prio=1 status=active | `- 5:0:0:3 sdk 8:160 active ready running `-+- policy='round-robin 0' prio=1 status=enabled `- 4:0:0:3 sdm 8:192 active ready running VMLHRStorage002 (14f504e46494c455233384b7353432d52454b4c2d79506757) dm-8 OPNFILER,VIRTUAL-DISK size=10G features='1 queue_if_no_path' hwhandler='0' wp=rw |-+- policy='round-robin 0' prio=1 status=active | `- 5:0:0:2 sdj 8:144 active ready running `-+- policy='round-robin 0' prio=1 status=enabled `- 4:0:0:2 sdl 8:176 active ready running VMLHRStorage001 (14f504e46494c455242674c7079392d753750482d63734443) dm-7 OPNFILER,VIRTUAL-DISK size=10G features='1 queue_if_no_path' hwhandler='0' wp=rw |-+- policy='round-robin 0' prio=1 status=active | `- 4:0:0:1 sdh 8:112 active ready running `-+- policy='round-robin 0' prio=1 status=enabled `- 5:0:0:1 sdi 8:128 active ready running VMLHRStorage000 (14f504e46494c455232326c6c76442d4361634f2d4d4f4d41) dm-6 OPNFILER,VIRTUAL-DISK size=10G features='1 queue_if_no_path' hwhandler='0' wp=rw |-+- policy='round-robin 0' prio=1 status=active | `- 4:0:0:0 sdf 8:80 active ready running `-+- policy='round-robin 0' prio=1 status=enabled `- 5:0:0:0 sdg 8:96 active ready running [root@raclhr-12cR1-N1 ~]# [root@raclhr-12cR1-N1 ~]# multipath -ll|grep LHR VMLHRStorage003 (14f504e46494c4552614e35626c6f2d4e794d702d4c344a6c) dm-9 OPNFILER,VIRTUAL-DISK VMLHRStorage002 (14f504e46494c455233384b7353432d52454b4c2d79506757) dm-8 OPNFILER,VIRTUAL-DISK VMLHRStorage001 (14f504e46494c455242674c7079392d753750482d63734443) dm-7 OPNFILER,VIRTUAL-DISK VMLHRStorage000 (14f504e46494c455232326c6c76442d4361634f2d4d4f4d41) dm-6 OPNFILER,VIRTUAL-DISK [root@raclhr-12cR1-N1 ~]#
|
启用multipath配置后,会在/dev/mapper下生成多路径逻辑盘
|
[root@raclhr-12cR1-N1 ~]# cd /dev/mapper [root@raclhr-12cR1-N1 mapper]# ll total 0 crw-rw---- 1 root root 10, 58 Jan 23 12:49 control lrwxrwxrwx 1 root root 7 Jan 23 12:49 vg_orasoft-lv_orasoft_soft -> ../dm-3 lrwxrwxrwx 1 root root 7 Jan 23 12:49 vg_orasoft-lv_orasoft_u01 -> ../dm-2 lrwxrwxrwx 1 root root 7 Jan 23 12:50 vg_rootlhr-Vol00 -> ../dm-1 lrwxrwxrwx 1 root root 7 Jan 23 12:50 vg_rootlhr-Vol01 -> ../dm-4 lrwxrwxrwx 1 root root 7 Jan 23 12:49 vg_rootlhr-Vol02 -> ../dm-0 lrwxrwxrwx 1 root root 7 Jan 23 12:50 vg_rootlhr-Vol03 -> ../dm-5 lrwxrwxrwx 1 root root 7 Jan 23 13:55 VMLHRStorage000 -> ../dm-6 lrwxrwxrwx 1 root root 7 Jan 23 13:55 VMLHRStorage001 -> ../dm-7 lrwxrwxrwx 1 root root 7 Jan 23 13:55 VMLHRStorage002 -> ../dm-8 lrwxrwxrwx 1 root root 7 Jan 23 13:55 VMLHRStorage003 -> ../dm-9 [root@raclhr-12cR1-N1 mapper]#
|
至此，多路径multipath配置完成。
在6.2之前配置multipath设备的权限只需要在设备配置里增加uid,gid,mode就可以
uid 1100 #uid
gid 1020 #gid
如：
|
multipath { wwid 360050763008101d4e00000000000000a alias DATA03 uid 501 #uid gid 501 #gid }
|
在6.2之后配置multipath配置文件里去掉uid,gid,mode这三个参数，需要使用udev使用,示例文件在/usr/share/doc/device-mapper-version中有一个模板文件,名为12-dm-permissions.rules,您可以使用它并将其放在 /etc/udev/rules.d 目录中使其生效。
|
[root@raclhr-12cR1-N1 rules.d]# ll /usr/share/doc/device-mapper-1.02.79/12-dm-permissions.rules -rw-r--r--. 1 root root 3186 Aug 13 2013 /usr/share/doc/device-mapper-1.02.79/12-dm-permissions.rules [root@raclhr-12cR1-N1 rules.d]# [root@raclhr-12cR1-N1 rules.d]# ll total 24 -rw-r--r-- 1 root root 77 Jan 23 18:06 12-dm-permissions.rules -rw-r--r-- 1 root root 190 Jan 23 15:40 55-usm.rules -rw-r--r-- 1 root root 549 Jan 23 15:17 70-persistent-cd.rules -rw-r--r-- 1 root root 585 Jan 23 15:09 70-persistent-net.rules -rw-r--r-- 1 root root 633 Jan 23 15:46 99-oracle-asmdevices.rules -rw-r--r-- 1 root root 916 Jan 23 15:16 99-oracleasm.rules [root@raclhr-12cR1-N1 rules.d]# more /etc/udev/rules.d/12-dm-permissions.rules ENV{DM_NAME}=="VMLHRStorage*", OWNER:="grid", GROUP:="asmadmin", MODE:="660" [root@raclhr-12cR1-N1 rules.d]#
|
将文件/etc/udev/rules.d/12-dm-permissions.rules复制到节点2上。
脚本如下所示：
|
for i in f g h i j k l m ; do echo "KERNEL==\"dm-*\", BUS==\"block\", PROGRAM==\"/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/\$name\",RESULT==\"`scsi_id --whitelisted --replace-whitespace --device=/dev/sd$i`\",NAME=\"asm-disk$i\",OWNER=\"grid\",GROUP=\"asmadmin\",MODE=\"0660\"" >> /etc/udev/rules.d/99-oracleasm.rules done
|
由于多路径的设置WWID有重复，所以应该去掉文件/etc/udev/rules.d/99-oracleasm.rules中的重复的行。
在节点1执行以下操作：
|
[root@raclhr-12cR1-N1 rules.d]# for i in f g h i j k l m ; > do > echo "KERNEL==\"dm-*\", BUS==\"block\", PROGRAM==\"/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/\$name\",RESULT==\"`scsi_id --whitelisted --replace-whitespace --device=/dev/sd$i`\",NAME=\"asm-disk$i\",OWNER=\"grid\",GROUP=\"asmadmin\",MODE=\"0660\"" >> /etc/udev/rules.d/99-oracleasm.rules > done
|
打开文件/etc/udev/rules.d/99-oracleasm.rules，去掉WWID重复的行只保留一行即可。
|
[root@raclhr-12cR1-N1 ~]# cat /etc/udev/rules.d/99-oracleasm.rules KERNEL=="dm-*", BUS=="block", PROGRAM=="/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/$name",RESULT=="14f504e46494c455232326c6c76442d4361634f2d4d4f4d41",NAME="asm-diskf",OWNER="grid",GROUP="asmadmin",MODE="0660" KERNEL=="dm-*", BUS=="block", PROGRAM=="/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/$name",RESULT=="14f504e46494c455242674c7079392d753750482d63734443",NAME="asm-diskh",OWNER="grid",GROUP="asmadmin",MODE="0660" KERNEL=="dm-*", BUS=="block", PROGRAM=="/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/$name",RESULT=="14f504e46494c455233384b7353432d52454b4c2d79506757",NAME="asm-diskj",OWNER="grid",GROUP="asmadmin",MODE="0660" KERNEL=="dm-*", BUS=="block", PROGRAM=="/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/$name",RESULT=="14f504e46494c4552614e35626c6f2d4e794d702d4c344a6c",NAME="asm-diskk",OWNER="grid",GROUP="asmadmin",MODE="0660" [root@raclhr-12cR1-N1 ~]#
|
将文件/etc/udev/rules.d/99-oracleasm.rules的内容拷贝到节点2，然后重启udev。
|
[root@raclhr-12cR1-N1 ~]# start_udev Starting udev: [ OK ] [root@raclhr-12cR1-N1 ~]# [root@raclhr-12cR1-N1 ~]# ll /dev/asm-* brw-rw---- 1 grid asmadmin 8, 32 Jan 23 15:50 /dev/asm-diskc brw-rw---- 1 grid asmadmin 8, 48 Jan 23 15:48 /dev/asm-diskd brw-rw---- 1 grid asmadmin 8, 64 Jan 23 15:48 /dev/asm-diske brw-rw---- 1 grid asmadmin 253, 7 Jan 23 15:46 /dev/asm-diskf brw-rw---- 1 grid asmadmin 253, 9 Jan 23 15:46 /dev/asm-diskh brw-rw---- 1 grid asmadmin 253, 6 Jan 23 15:46 /dev/asm-diskj brw-rw---- 1 grid asmadmin 253, 8 Jan 23 15:46 /dev/asm-diskk [root@raclhr-12cR1-N1 ~]# [grid@raclhr-12cR1-N1 ~]$ $ORACLE_HOME/bin/kfod disks=all s=true ds=true -------------------------------------------------------------------------------- Disk Size Header Path Disk Group User Group ================================================================================ 1: 6144 Mb MEMBER /dev/asm-diskc OCR grid asmadmin 2: 10240 Mb MEMBER /dev/asm-diskd DATA grid asmadmin 3: 10240 Mb MEMBER /dev/asm-diske FRA grid asmadmin 4: 10240 Mb CANDIDATE /dev/asm-diskf # grid asmadmin 5: 10240 Mb CANDIDATE /dev/asm-diskh # grid asmadmin 6: 10240 Mb CANDIDATE /dev/asm-diskj # grid asmadmin 7: 10240 Mb CANDIDATE /dev/asm-diskk # grid asmadmin -------------------------------------------------------------------------------- ORACLE_SID ORACLE_HOME ================================================================================ +ASM2 /u01/app/12.1.0/grid +ASM1 /u01/app/12.1.0/grid [grid@raclhr-12cR1-N1 ~]$ asmcmd
ASMCMD> lsdg State Type Rebal Sector Block AU Total_MB Free_MB Req_mir_free_MB Usable_file_MB Offline_disks Voting_files Name MOUNTED EXTERN N 512 4096 1048576 10240 6487 0 6487 0 N DATA/ MOUNTED EXTERN N 512 4096 1048576 10240 10144 0 10144 0 N FRA/ MOUNTED EXTERN N 512 4096 1048576 6144 1672 0 1672 0 Y OCR/ ASMCMD> lsdsk Path /dev/asm-diskc /dev/asm-diskd /dev/asm-diske ASMCMD> lsdsk --candidate -p Group_Num Disk_Num Incarn Mount_Stat Header_Stat Mode_Stat State Path 0 1 0 CLOSED CANDIDATE ONLINE NORMAL /dev/asm-diskf 0 3 0 CLOSED CANDIDATE ONLINE NORMAL /dev/asm-diskh 0 2 0 CLOSED CANDIDATE ONLINE NORMAL /dev/asm-diskj 0 0 0 CLOSED CANDIDATE ONLINE NORMAL /dev/asm-diskk ASMCMD>
|
CREATE DISKGROUP FRA external redundancy DISK '/dev/asm-diskf','/dev/asm-diskh' ATTRIBUTE 'compatible.rdbms' = '12.1', 'compatible.asm' = '12.1';
|
SQL> select path from v$asm_disk;
PATH -------------------------------------------------------------------------------- /dev/asm-diskk /dev/asm-diskf /dev/asm-diskj /dev/asm-diskh /dev/asm-diske /dev/asm-diskd /dev/asm-diskc
7 rows selected.
SQL> CREATE DISKGROUP TESTMUL external redundancy DISK '/dev/asm-diskf','/dev/asm-diskh' ATTRIBUTE 'compatible.rdbms' = '12.1', 'compatible.asm' = '12.1';
Diskgroup created.
SQL> ASMCMD> lsdg State Type Rebal Sector Block AU Total_MB Free_MB Req_mir_free_MB Usable_file_MB Offline_disks Voting_files Name MOUNTED EXTERN N 512 4096 1048576 10240 6487 0 6487 0 N DATA/ MOUNTED EXTERN N 512 4096 1048576 10240 10144 0 10144 0 N FRA/ MOUNTED EXTERN N 512 4096 1048576 6144 1672 0 1672 0 Y OCR/ MOUNTED EXTERN N 512 4096 1048576 20480 20381 0 20381 0 N TESTMUL/ ASMCMD>
[root@raclhr-12cR1-N1 ~]# crsctl stat res -t | grep -2 TESTMUL ONLINE ONLINE raclhr-12cr1-n1 STABLE ONLINE ONLINE raclhr-12cr1-n2 STABLE ora.TESTMUL.dg ONLINE ONLINE raclhr-12cr1-n1 STABLE ONLINE ONLINE raclhr-12cr1-n2 STABLE [root@raclhr-12cR1-N1 ~]#
|
|
[oracle@raclhr-12cR1-N1 ~]$ sqlplus / as sysdba
SQL*Plus: Release 12.1.0.2.0 Production on Mon Jan 23 16:17:28 2017
Copyright (c) 1982, 2014, Oracle. All rights reserved.
Connected to: Oracle Database 12c Enterprise Edition Release 12.1.0.2.0 - 64bit Production With the Partitioning, Real Application Clusters, Automatic Storage Management, OLAP, Advanced Analytics and Real Application Testing options
SQL> create tablespace TESTMUL datafile '+TESTMUL' size 10M;
Tablespace created.
SQL> select name from v$datafile;
NAME -------------------------------------------------------------------------------- +DATA/LHRRAC/DATAFILE/system.258.933550527 +DATA/LHRRAC/DATAFILE/undotbs2.269.933551323 +DATA/LHRRAC/DATAFILE/sysaux.257.933550483 +DATA/LHRRAC/DATAFILE/undotbs1.260.933550575 +DATA/LHRRAC/DATAFILE/example.268.933550723 +DATA/LHRRAC/DATAFILE/users.259.933550573 +TESTMUL/LHRRAC/DATAFILE/testmul.256.934042679
7 rows selected.
SQL>
|
将存储停掉一块网卡eth2：
|
[root@OFLHR ~]# ip a 1: lo: mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:0c:29:98:1a:cd brd ff:ff:ff:ff:ff:ff inet 192.168.59.200/24 brd 192.168.59.255 scope global eth0 inet6 fe80::20c:29ff:fe98:1acd/64 scope link valid_lft forever preferred_lft forever 3: eth2: mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:0c:29:98:1a:d7 brd ff:ff:ff:ff:ff:ff inet 192.168.2.200/24 brd 192.168.2.255 scope global eth2 inet6 fe80::20c:29ff:fe98:1ad7/64 scope link valid_lft forever preferred_lft forever [root@OFLHR ~]# ifconfig eth2 down [root@OFLHR ~]# ip a 1: lo: mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:0c:29:98:1a:cd brd ff:ff:ff:ff:ff:ff inet 192.168.59.200/24 brd 192.168.59.255 scope global eth0 inet6 fe80::20c:29ff:fe98:1acd/64 scope link valid_lft forever preferred_lft forever 3: eth2: mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:0c:29:98:1a:d7 brd ff:ff:ff:ff:ff:ff inet 192.168.2.200/24 brd 192.168.2.255 scope global eth2 [root@OFLHR ~]#
|
rac节点查看日志：
|
[root@raclhr-12cR1-N1 ~]# tail -f /var/log/messages Jan 23 16:20:51 raclhr-12cR1-N1 iscsid: connect to 192.168.2.200:3260 failed (No route to host) Jan 23 16:20:57 raclhr-12cR1-N1 iscsid: connect to 192.168.2.200:3260 failed (No route to host) Jan 23 16:21:03 raclhr-12cR1-N1 iscsid: connect to 192.168.2.200:3260 failed (No route to host) [root@raclhr-12cR1-N1 ~]# multipath -ll VMLHRStorage003 (14f504e46494c4552614e35626c6f2d4e794d702d4c344a6c) dm-8 OPNFILER,VIRTUAL-DISK size=10G features='1 queue_if_no_path' hwhandler='0' wp=rw `-+- policy='round-robin 0' prio=1 status=active |- 5:0:0:3 sdm 8:192 failed faulty running `- 4:0:0:3 sdl 8:176 active ready running VMLHRStorage002 (14f504e46494c455233384b7353432d52454b4c2d79506757) dm-9 OPNFILER,VIRTUAL-DISK size=10G features='1 queue_if_no_path' hwhandler='0' wp=rw `-+- policy='round-robin 0' prio=1 status=active |- 5:0:0:2 sdj 8:144 failed faulty running `- 4:0:0:2 sdk 8:160 active ready running VMLHRStorage001 (14f504e46494c455242674c7079392d753750482d63734443) dm-7 OPNFILER,VIRTUAL-DISK size=10G features='1 queue_if_no_path' hwhandler='0' wp=rw `-+- policy='round-robin 0' prio=1 status=active |- 4:0:0:1 sdi 8:128 active ready running `- 5:0:0:1 sdh 8:112 failed faulty running VMLHRStorage000 (14f504e46494c455232326c6c76442d4361634f2d4d4f4d41) dm-6 OPNFILER,VIRTUAL-DISK size=10G features='1 queue_if_no_path' hwhandler='0' wp=rw `-+- policy='round-robin 0' prio=1 status=active |- 4:0:0:0 sdf 8:80 active ready running `- 5:0:0:0 sdg 8:96 failed faulty running [root@raclhr-12cR1-N1 ~]#
|
表空间可以正常访问：
|
SQL> create table tt tablespace TESTMUL as select * from dual;
Table created.
SQL> select * from tt;
D - X
SQL>
|
同理，将eth2进行up，而将eth0宕掉，表空间依然正常。重启集群和存储后，集群一切正常。
重新搭建一套多路径的环境来测试多路径。
最简单的测试方法，是用dd往磁盘读写数据，然后用iostat观察各通道的流量和状态，以判断Failover或负载均衡方式是否正常：
# dd if=/dev/zero of=/dev/mapper/mpath0
# iostat -k 2
|
[root@orcltest ~]# multipath -ll VMLHRStorage003 (14f504e46494c4552674a61727a472d523449782d5336784e) dm-3 OPNFILER,VIRTUAL-DISK size=10G features='1 queue_if_no_path' hwhandler='0' wp=rw `-+- policy='round-robin 0' prio=1 status=active |- 35:0:0:2 sdf 8:80 active ready running `- 36:0:0:2 sdg 8:96 active ready running VMLHRStorage002 (14f504e46494c4552506a5a5954422d6f6f4e652d34423171) dm-2 OPNFILER,VIRTUAL-DISK size=10G features='1 queue_if_no_path' hwhandler='0' wp=rw `-+- policy='round-robin 0' prio=1 status=active |- 35:0:0:3 sdh 8:112 active ready running `- 36:0:0:3 sdi 8:128 active ready running VMLHRStorage001 (14f504e46494c4552324b583573332d774e5a622d696d7334) dm-1 OPNFILER,VIRTUAL-DISK size=10G features='1 queue_if_no_path' hwhandler='0' wp=rw `-+- policy='round-robin 0' prio=1 status=active |- 35:0:0:1 sdd 8:48 active ready running `- 36:0:0:1 sde 8:64 active ready running VMLHRStorage000 (14f504e46494c45523431576859532d643246412d5154564f) dm-0 OPNFILER,VIRTUAL-DISK size=10G features='1 queue_if_no_path' hwhandler='0' wp=rw `-+- policy='round-robin 0' prio=1 status=active |- 35:0:0:0 sdb 8:16 active ready running `- 36:0:0:0 sdc 8:32 active ready running [root@orcltest ~]# dd if=/dev/zero of=/dev/mapper/VMLHRStorage001
|
重新开一个窗口执行iostat -k 2可以看到：
|
avg-cpu: %user %nice %system %iowait %steal %idle 0.00 0.00 5.23 20.78 0.00 73.99
Device: tps kB_read/s kB_wrtn/s kB_read kB_wrtn sda 9.00 0.00 92.00 0 184 scd0 0.00 0.00 0.00 0 0 sdb 0.00 0.00 0.00 0 0 sdc 0.00 0.00 0.00 0 0 sdd 1197.50 4704.00 10886.00 9408 21772 sde 1197.50 4708.00 10496.00 9416 20992 sdh 0.00 0.00 0.00 0 0 sdi 0.00 0.00 0.00 0 0 sdf 0.00 0.00 0.00 0 0 sdg 0.00 0.00 0.00 0 0 dm-0 0.00 0.00 0.00 0 0 dm-4 0.00 0.00 0.00 0 0 dm-10 0.00 0.00 0.00 0 0 dm-1 2395.00 9412.00 21382.00 18824 42764 dm-2 0.00 0.00 0.00 0 0 dm-3 0.00 0.00 0.00 0 0 dm-5 0.00 0.00 0.00 0 0 dm-6 0.00 0.00 0.00 0 0 dm-7 0.00 0.00 0.00 0 0 dm-8 0.00 0.00 0.00 0 0 dm-9 0.00 0.00 0.00 0 0
|
用multipath生成映射后，会在/dev目录下产生多个指向同一条链路的设备：
|
/dev/mapper/mpathn /dev/mpath/mpathn /dev/dm-n |
但它们的来源是完全不同的：
/dev/mapper/mpathn 是multipath虚拟出来的多路径设备，我们应该使用这个设备；/dev/mapper 中的设备是在引导过程中生成的。可使用这些设备访问多路径设备，例如在生成逻辑卷时。
/dev/mpath/mpathn 是udev设备管理器创建的，实际上就是指向下面的dm-n设备，仅为了方便，不能用来挂载；提供 /dev/mpath 中的设备是为了方便，这样可在一个目录中看到所有多路径设备。这些设备是由 udev 设备管理器生成的，且在系统需要访问它们时不一定能启动。请不要使用这些设备生成逻辑卷或者文件系统。
/dev/dm-n 是软件内部自身使用的，不能被软件以外使用，不可挂载。所有 /dev/dm-n 格式的设备都只能是作为内部使用，且应该永远不要使用。
简单来说，就是我们应该使用/dev/mapper/下的设备符。对该设备即可用fdisk进行分区，或创建为pv。
好了，有关使用OpenFiler来模拟存储配置RAC中ASM共享盘及多路径的测试就到此为止了。2016年结束了，今天是1月23日，明天是1月24日，小麦苗回家过年了，O(∩_∩)O~。在此也祝福各位网友和朋友身体健康，万事如意，合家欢乐，生活美满，事业有成，珠玉满堂，多寿多富，财大气粗，攻无不克，战无不胜!
About Me
...............................................................................................................................
● 本文作者：小麦苗，只专注于数据库的技术，更注重技术的运用
● 本文在itpub（http://blog.itpub.net/26736162）、博客园（http://www.cnblogs.com/lhrbest）和个人微信公众号（xiaomaimiaolhr）上有同步更新
● 本文itpub地址：http://blog.itpub.net/26736162/viewspace-2132858/
● 本文博客园地址：http://www.cnblogs.com/lhrbest/p/6345157.html
● 本文pdf版及小麦苗云盘地址：http://blog.itpub.net/26736162/viewspace-1624453/
● QQ群：230161599 微信群：私聊
● 联系我请加QQ好友(642808185)，注明添加缘由
● 于 2017-01-22 08:00 ~ 2016-01-23 24:00 在农行完成
● 文章内容来源于小麦苗的学习笔记，部分整理自网络，若有侵权或不当之处还请谅解
● 版权所有，欢迎分享本文，转载请保留出处
...............................................................................................................................
拿起手机使用微信客户端扫描下边的左边图片来关注小麦苗的微信公众号：xiaomaimiaolhr，扫描右边的二维码加入小麦苗的QQ群，学习最实用的数据库技术。
免责声明：本站发布的内容（图片、视频和文字）以原创、转载和分享为主，文章观点不代表本网站立场，如果涉及侵权请联系站长邮箱：is@yisu.com进行举报，并提供相关证据，一经查实，将立刻删除涉嫌侵权内容。